Home LEADProductsManufacturingNewsContact



APVMA Code :60940

Active Constituent(s): 500g/L iprodione
Registered For:


 Commercial use

 Domestic use

Overview: For control of certain fungal diseases in various crops and situations.

Chemical Group dicarboximide


 SDS (292.9 KB)

 Label (307.9 KB)





Subscribe Fungicide is a member of the Dicarboximide group of fungicides. For fungicide resistance management the product is a Group 2 fungicide. Some naturally occurring individual fungi resistant to the product and other Group 2 fungicides may exist through normal genetic variability in any fungal population. The resistant individuals can eventually dominate the fungal population if these fungicides are used repeatedly. These resistant fungi will not be controlled by this Subscribe or other Group 2 fungicides, thus resulting in a reduction in efficacy and possible yield loss.


Since the occurrence of resistant fungi is difficult to detect prior to use, Cheminova Australia Pty. Ltd. accepts no liability for any losses that may result from the failure of this product to control resistant fungi.



Note: Subscribe may be unstable in conditions where the pH is 7 or higher. It is therefore essential to check the pH of the spray solution before adding Subscribe.  A suitable registered buffering agent may have to be added to bring pH down below 7. Add the required amount of Subscribe to the spray tank containing half the required volume of water. Mix thoroughly and make up to the required volume with water.



This product acts very rapidly and where the turf is of a low nutritional status, a slight yellowing may be seen. This will be corrected by nitrogenous fertilizer application. Where possible, it is recommended that the fertilizer program should precede the fungicide application.



Good disease control requires even, thorough coverage of the target area. Application should be made using sufficient water to ensure thorough coverage.


Tree and Vine Crops

Dilute Spraying

Use a sprayer designed to apply high volumes of water up to the point of run-off and matched to the crop being sprayed. Set up and operate the sprayer to achieve even coverage throughout the crop canopy. Apply sufficient water to cover the crop to the point of run-off. Avoid excessive run-off. The required water volume may be determined by applying different test volumes, using different settings on the sprayer, from industry guidelines or expert advice. Add the amount of product specified in the Directions For Use table for each 100 L of water. Spray to the point of run-off. The required dilute spray volume will change and the sprayer set up and operation may also need to be changed, as the crop grows.


Concentrate Spraying

Use a sprayer designed and set up for the concentrate spraying (that is a sprayer which applies water volumes less than those required to reach the point of run-off) and matched to the crop being sprayed. Set up and operate the sprayer to achieve even coverage throughout the crop canopy using your chosen water volume. Determine an appropriate dilute spray volume (See Dilute Spraying above) for the crop canopy. This is needed to calculate the concentrate mixing rate. The mixing rate for concentrate can then be calculated in the following way:



1. Dilute spray volume as determined above: For example 1500 L/ha.

2. Your chosen concentrate spray volume: For example 500 L/ha.

3. The concentration factor in this example is: 3x (ie 1500 L ÷ 500 L = 3).

4. If the dilute label rate is 10 mL/100 L, then the concentrate rate becomes 3 x 10, that is 30 mL/100 L of concentrate spraying.  The chosen spray volume, amount of product per 100 L of water, and the sprayer set up and operation may need to be changed as the crop grows.


For further information on concentrate spraying, users are advised to consult relevant industry guidelines, undertake appropriate competency training and follow industry Best Practices.



Export produce or animals must have appropriate residue tolerance limits established in the importing countries and any residues must not exceed the tolerance limit.



This product may be combined with: fosetyl-aluminium, calcium chloride, Cyren®, copper oxychloride, Danadim®, mancozeb, fenitrothion, dicofol, Fyfanon®, metalaxyl and methomyl.

With any mixture, thoroughly agitate immediately before applying. It is not recommended to mix this product with more than one of the above chemicals in the tank.  DO NOT tank mix this product with fertilisers.  Mixing Subscribe with fosetyl-aluminium may result in some settling out. As formulations of other manufacturer’s products are beyond the control of CHEMINOVA AUSTRALIA Pty. Ltd., all mixtures should be tested prior to mixing commercial quantities.



Toxic to aquatic organisms. DO NOT contaminate streams, rivers or waterways with chemical or used containers.



Keep out of reach of children. Store in the closed, original container in a cool, secure, well-ventilated area. DO NOT

store for prolonged periods indirect sunlight. Protect from frost.


The method of disposal of the container depends on the container type. Read the ‘Storage and Disposal’ instructions on the label that is attached to the container.

Non-returnable containers only

Triple or preferably pressure rinse containers before disposal. Add rinsings to the spray tank. DO NOT dispose of undiluted chemicals on site. If recycling, replace cap and return clean containers to recycler or designated collection point. If not recycling, break, crush, or puncture and deliver empty packaging for appropriate disposal to an approved waste management facility. If an approved waste management facility is not available bury the empty packaging 500 mm below the surface in a disposal pit specifically marked and set up for this purpose clear of waterways, desirable vegetation and tree roots, in compliance with relevant Local, State or Territory government regulations. DO NOT burn empty containers or product.

100, 110L

Do not remove or tamper with the dry valves or security seal. Do not contaminate the drum with water or any other foreign matter. After each use of the product ensure that the dry valve coupler, delivery system and hoses are disconnected, triple rinsed with clean water and drained accordingly. When the drum is empty remove the dry valve coupler and return to the point of purchase.


Store in the closed, original container in a cool, well-ventilated area. Do not store for prolonged periods in direct sunlight.

Empty contents fully into application equipment. Close all valves and return to point of supply for refill or storage.



May irritate the eyes. Avoid contact with eyes. When opening the container and using the product wear cotton overalls buttoned to the neck and wrist or equivalent clothing, elbow-length PVC gloves and face shield. Wash hands after use. After each day’s use, wash gloves, face shield and contaminated clothing.



If poisoning occurs, contact a doctor or Poisons Information Centre. Phone Australia 131126.





This product must be used, handled and stored strictly as directed in accordance with this label, packaging and other reference material (“Directions”). To the extent permitted by law Cheminova Pty Ltd and its related companies will have no liability for any injury, loss or damage arising from a failure to follow the Directions. 

Product details last updated on 26 June 2015


DISCLAIMER: This is not the SUBSCRIBE FUNGICIDE label. To view or print the label for this product, click the "MSDS/Label" tab at the top of this page. Always follow label instructions.


For specialist advice in an EMERGENCY only phone 1800 033 111, TOLL-FREE, ALL-HOURS, NATIONWIDE

To the topTo the top
Alphabetical index  Ι  Sitemap  Ι  Disclaimer  Ι  Sales terms and conditions  Ι  Useful links